AUDIO
AMP
  • 맨리 네오 클래식 250 와트 올 튜브 모노블록

맨리 네오 클래식 250 와트 올 튜브 모노블록

0
19,600,000원
공유
구매혜택
할인적용 : 적립 마일리지 :

 

 

250mono_1_153552_170655.jpg
250mono_2_153604_170706.jpg

 

 

Delivering emotion and translating with pure seductive capabilities the essence of music, the Neo-Classic 250 relies on decades of circuit refinement with proven componentry that maximizes this classic push-pull design. Choose either the sonically seductive qualities of triode or the more powerful tetrode configuration. The big beefy capacitors provide instant energy for dynamic performance of transient peaks and powerful bass impact.

 

DETAILS

 


A magazine reviewer once wrote the following about the Manley 250's: "In triode mode a pair of Manleys produces a remarkably three dimensional soundfield that is both convincing and seductive. When switched into tetrode mode, the Manleys have the brawn to deliver a full symphony orchestra directly into your living room." "When I listened through the same cut through the triode mode tube amps, I cried. Yup, tears ran down my cheeks while I bounced up and down, waving my arms, physically buffeted by the raw emotion of the music. Emotion- that essential component at the very core of great music. The Manleys pass through that emotional information, but the (solid-state amps) don't." Tried and true: The Manley 500 and 250 Watt Monoblocks are our most powerful push-pull production-models. Both the circuit design and the selected componentry have been refined over years and years of development. Reliability that you can depend upon combined with musical accuracy and emotional authority is what these amplifiers promise- and deliver. They are able to switch operation modes allowing the listener to choose between the sonically seductive qualities of triode and the more powerful Ultra-Linear configuration. We use big, beefy reservoir capacitors in the high voltage supplies giving plenty of instant energy for dynamic performance of transient peaks and bass impact and weight which often exceeds that of rival solid-state amplifiers. We run high voltages on the plates of the output tubes but operate them at lower current which will result in their longer life. Although each output tube has its own bias-adjust, We carefully fit each amplifier with computer-batched tubes for optimum performance. The bias adjustment pots and measuring points are conveniently located behind the oval front panel insert.

 

 

To avoid a heavy power drain when the cold amplifier is first switched on, we conceived a "Soft-Start" mode which also functions as an "Ever-Warm" position allowing the amplifiers to be always warmed up for pleasurable listening. Each amplifier only consumes 30 watts of power in Ever-Warm mode. A blinking green LED reminds the user that the amplifier is in warm-up mode because as all the power supplies are at half-voltage, the amplifier will still operate at half power when the Ever-Warm mode is engaged, so the user should use the MUTE switch when in this mode.

 

The front-panel mute switch and angled-back chassis make it easier to hook up the interconnects, speaker cables, and IEC power cord.

In our own in-house magnetics department, our R&D team completely redesigned all of our output transformers in 1998 with the goal to reclaim that luscious rich mid-range of our vintage designs. In 2013 we reworked the output transformer to operate the output stage in Ultra-Linear mode which is a great sounding balance between the detail of triode and the brawn of Tetrode. We also specifically set out to achieve a deeper bottom register at higher power with lower distortion. Hours and hours of listening tests, measurements, and fine-tuning brought an exciting and stunning result to our ears. We hope you will agree.

 

[제품 사양]

 

 

ALL-TUBE monoblock design: uses 10 x Tungsol EL34B output tubes
Driver Stage: High current double 12BH7EH (x2) Electro-Harmonix Russian
Input Tube: Tungsol 12AT7 large plate
BALANCED & UNBALANCED inputs: RCA and XLR jacks (switchable)
MUTE switch: on front panel
TRIODE / Ultra-Linear output mode switching: on front panel
SOFT-START turn on mode: minimizes in-rush current by first powering up amplifier to half voltages
EVER-WARM mode: for standby keeps tubes warmed up at half voltages
MANLEY Precision Output Transformer: designed and wound at Manley Labs
Front panel bias measurement and adjust: Concealed under the black oval insert
Output Tube Standing Current: 27.5mA
Set Bias for: 275mVDC measured across each bias tip jack to ground
Large filter / reservoir capacitors: 3800uF x 2
Angled rear of chassis: provides for easy connections
WBT binding posts: CE compliant for European models
Input Sensitivity RCA: Triode = 1.637 V, Tetrode = 1.837 V for full power
Input Sensitivity XLR: Triode = 3.2 V, Tetrode = 3.6 V for full power
Input Sensitivity Triode: 174mV for 1 watt into 8 Ohms
Input Sensitivity Tetrode: 146mV for 1 watt into 8 Ohms
Gain Triode: 30dB
Gain Tetrode: 32dB
Input Impedance RCA: 116 kOhm @ 1KHz
Input Impedance XLR: 270 kOhm @ 1KHz; 20 kOhms @ 20KHz; 38 kOhm @ 20Hz
Actual Output Impedance Triode: 0.538 Ohm
Actual Output Impedance Tetrode: 0.465 Ohm
Optimum Speaker Load: 5 Ohms
Damping Factor Triode: 14.8
Damping Factor Tetrode: 17.2
S/N Ratio Ref 1W into 8 Ohms: -80 dB; -90dB A-WGT
Dynamic Range: 93dB
FLAT frequency response: 10 Hz - 30 KHz continuous
Full Power Tetrode: 250W @ 1.5% THD into 5 Ohms
Full Power Triode: 100W @ 1.5% THD into 5 Ohms
Power Consumption: 30 Watts in "EVER-WARM" mode
Maximum Power Consumption: 815 Watts at full power
Operating Mains Voltage: Factory set for 100V, 120V or 220-240VAC operation for original destination country's mains voltage.
Operating Mains Voltage: changeable with power transformer re-wiring and fuse value change.
Mains Voltage Frequency:
Mains Fuse 100-120VAC operation: MDA 10 Amp SLO-BLO Ceramic Time-Delay fuse
Mains Fuse 220-240VAC operation: MDA 8 Amp SLO-BLO Ceramic Time-Delay fuse
B+ Fuse: MDA 1 1/2A SLO-BLO Ceramic Time-Delay fuse
Badge Illumination: Units produced before 4/2003 use 8V, 0.3A "Fuse-Lamp" 1/4" X 1 1/4"
- Serial numbers after N250188 use LED illumination which probably won't burn out
Power Cord: Detachable IEC standard. Appropriate power cord supplied for destination country
Unit Dimensions: W=19" x D=13" x H=9" each
Unit Weight: 68 Lbs. each
Shipping Weight: 73 Lbs. each

 

배송안내

- 오전 12시까지 입금이 확인된 상품에 한해 당일 출고가 진행되며, 재고 소진 제품, 수입제품 또는 주문 후 제작이 진행되는 상품의 경우 특성상 배송이 지연될 수 있습니다

- 배송은 택배, 화물배송, 직접 설치 등 상품의 특성에 가장 적합한 방법으로 진행됩니다.

- 오디오, 가구 등 일부 상품의 경우 지역(제주, 도서 산간) 또는 제품 특성에 따라 추가배송비 입금 요청이 있을 수 있습니다.

- 입고 예정인 제품을 함께 주문할 경우, 입고 후 통합 배송이 이루어집니다. 만약 기간 소요가 없는 일반 제품을 먼저 수령하기 원하실 경우 별도 주문을 해 주시길 바랍니다.

- 특정 제품에 한해 배송, 설치가 별도로 진행될 수 있습니다.


택배배송

- 평균 배송 기간은 주말제외, 3 ~ 7일이 소요됩니다.

 

화물배송(서울, 경기) 

- 부피가 큰 오디오나 가구, 조명의 경우 화물 배송을 진행하며 특정 제품에 한해 별도의 운송비가 부과될 수 있습니다.

- 배송 이외 설치가 필요한 경우 별도 설치 비용이 청구될 수 있습니다. 품목에 따라 직원 안내에 따라 배송 및 설치비 지급방식을 결정이 진행됩니다. 

- 채널 오디오의 경우 배송지에서 제품 배송 이외에 케이블링, 네트워킹 작업이 이루어 집니다

교환 및 반품안내

취소 및 교환은 소비자보호법 및 전자상거래 소비자보호에 관한 법률과 공정거래위원회의 소비자분쟁 해결기준에 따라 처리됩니다


교환

배송 완료 후 상품 자체의 하자가 발견되어 7일 이내에 고객센터로 접수하여 주신 경우에만 교환이 가능하며 그 이후에는 어떠한 경우라도 반품이 불가합니다.

- 상품이 불량인 경우, 주문한 내역과 다른 상품이 배송된 경우, 배송과정 중 파손된 경우 30일 이내에 청약철회 가능하며 배송비는 판매자가 부담합니다. 

- 제품의 하자 혹은 파손 사유가 아닌 단순 변심으로 인한 교환 (색상, 사이즈 교환 등) 1회에 한하며, 구매자 측에서 교환 관련 비용 전액 (수입진행 비용 및 국내배송에 소요된 비용)을 부담합니다.

- 상품의 내용이 표시, 광고의 내용과 다르거나 계약 내용과 다르게 이행된 경우 공급받은 날로부터 3개월 이내, 그 사실을 인지한 날로부터 30일 이내에 청약철회 가능합니다.

제품 하자 혹은 배송 시 파손으로 인한 교환 비용은 공급자가 부담합니다.

네이버페이로 결제한 제품의 교환, 반품 신청 시 해당 처리 가능여부 파악 및 일정 확인을 위해 담당부서에서 검토 후 교환, 반품 안내가 이루어집니다.

일부 상품은 신모델 출시, 부품 가격 변동 등 제조사 사정으로 인한 가격 및 대체상품이 변동될 수 있습니다.

 

아래와 같은 경우, 어떠한 경우라도 교환 및 환불이 불가합니다 

상품 수령일로부터 7일 이내, 반품의사를 밝히지 않은 경우

고객님의 책임 있는 사유로 상품 등이 멸실 또는 훼손된 경우

고객님의 사용 또는 일부 소비에 의하여 상품의 가치가 현저히 감소한 경우

고객님의 책임 있는 사유로 상품 등이 멸실 또는 훼손된 경우

부적절한 취급(아세톤 등의 화학물질) 또는 부주의(무리한 힘, 날카로운 것)로 인한 파손 및 고장의 경우

제품의 사용목적 이외의 사용, 개조 등으로 일어난 파손 또는 고장의 경우

지류 및 필기구

목재 가구의 경우 원목 특성인 직사광선, ·난방기구, 가습기 등에 의한 변형 (수축 및 팽창으로 인한 갈라짐) 또는 변색의 경우

천연가죽 특성의 불규칙한 가죽패턴, 가축의 성장과정에서 발생하는 가죽의 상처나 자국이 있는 경우

사용감에 다른 천연가죽의 자연스러운 주름이나 늘어남 현상 및 패브릭의 색 빠짐 현상(변색)의 경우

- 철재 도금 제품의 제작 공정상 불가피한 사항으로 색을 입히는 작업 과정에서 색상 톤의 미세한 차이, 표면이 매끄럽지 않거나, 도금 얼룩 및 스크래치가 일부분 있는 경우

배송 완료 후의 나무, 가죽, 패브릭, 오리털 특유의 냄새로 인한 경우

패브릭 직조에 따라 약간의 색상 차이가 느껴지는 경우

디스플레이 제품 구매 시

- 보내실 때에는 상품과 상품의 택, 포장박스 등 보내드린 구성품 그대로 반송해 주셔야 교환이 가능합니다 

- 교환/환불 의사를 통보하지 않고 반품하실 경우, 보류 상태(미처리)가 되니, 고객센터로 의사를 밝혀 주시길 바랍니다 


환불안내

- 환불 신청은 상품 수령일로부터 7일 이내 신청 가능합니다.

- 상품 회수 후 영업일 7일 이내에 결제 금액을 환불해 드립니다. 

- 상품 출고 이후 환불요청 시 상품 회수 후 처리됩니다.

- 결제일에 맞추어 대금이 청구될 경우 익월 신용카드 대금 청구 시 카드사에서 환급처리 됩니다.

- 신용카드결제 완료 후에는 사이트에서 주문을 취소할 수 없으므로 반드시 고객센터로 연락 주시길 바랍니다.


AS안내

- 브랜드 별 상품설명에 별도로 기입된 AS기준이 우선으로 적용되며 고객 비용부담으로 진행됩니다

- 일부 완제품으로 수입된 상품의 경우 A/S가 불가능합니다. (수입가구, 조명류)

비밀번호 인증

글 작성시 설정한 비밀번호를 입력해 주세요.

닫기

장바구니 담기

상품이 장바구니에 담겼습니다.
바로 확인하시겠습니까?

찜 리스트 담기

상품이 찜 리스트에 담겼습니다.
바로 확인하시겠습니까?